PDS_VERSION_ID                = PDS3
LABEL_REVISION_NOTE       = "
   2014-06-30, Rob Wilson, initial draft;                                    "
   RECORD_TYPE                        = STREAM

OBJECT            = DATA_SET
  DATA_SET_ID                 = "JUNO-J/SW-JAD-2-UNCALIBRATED-V1.0"

  OBJECT          = DATA_SET_INFORMATION
    DATA_SET_NAME             = "JUNO-J/SW-JAD-2-UNCALIBRATED-V1.0"
    DATA_SET_COLLECTION_MEMBER_FLG = N
    START_TIME                = NULL
    STOP_TIME                 = NULL
    DATA_SET_RELEASE_DATE     = NULL
    PRODUCER_FULL_NAME        = "ROBERT J WILSON"
    DETAILED_CATALOG_FLAG     = N
    DATA_OBJECT_TYPE          = "TABLE"

    DATA_SET_TERSE_DESC       = "This data set consists of all of the
uncalibrated data collected by the JADE (Jovian Auroral Plasma
Distributions Experiment) on-board the Juno spacecraft.
For more information about the instrument and data sets, see
[MCCOMAS2013] and [WILSON2014]."
    CITATION_DESC             = UNK
    ABSTRACT_DESC             = NULL
    DATA_SET_DESC             = "
                           Needs to be filled, but so far (2014) we only
                           have science data used for engineering testing,
                           and of limited use for scientists."

    CONFIDENCE_LEVEL_NOTE           = "

  Review
  ======
    These data have been reviewed by the instrument team and are of the
    highest quality that can be generated at this time. After submission to
    the PDS, these data will be approved through the peer review process.


  Data Coverage and Quality
  =========================

    Gaps (This section copied from Cassini CAPS, but is likely true for JADE)
    ----
      There are many gaps in the JADE data stream and there are many
      different sources for these gaps.  Sources of gaps are as follows:
         a. telemety outages
         b. data policing violations
         c. incorrect spacecraft data mangement commanding
         d. telemetry commanding during Cruise
         e. instrument anomalies
         f. instrument modes which don't return all data products
         g. planned instrument power-off and/or sleep periods
      When there is no data for a time period, one of the above sources is
      the reason behind the gap.  There is no indicator to which of the
      sources is responsible for the gap in data coverage.

    Poor Data
    ---------
      When the instrument transmitts the data, there is an associated
      checksum that is checked during decompression.  If the checksum is
      incorrect, then that packet is discarded and never makes it to PDS.
      (Because the JADE data is zipped, a bad checksum means we don't know
      where the zipping ends, so can not decompress it.)

    Sensor Gains
    ------------
      Sensor gains were set for each sensor based upon calibration
      information determined on the ground.  While in-flight, sensor
      calibrations were performed and adjustments were made to the gain of a
      sensor, based upon interpretation of the data by the team and the
      leader of the sensor.

    Anomalies
    ---------
      None yet

  Limitations
  ===========
      The main limitation to using this data set is that the data are not
      calibrated.  Please use the CALIBRATED data set for calibrated data."


  END_OBJECT      = DATA_SET_INFORMATION

  OBJECT                      = DATA_SET_TARGET
    TARGET_NAME               = "JUPITER"
  END_OBJECT                  = DATA_SET_TARGET

  OBJECT                      = DATA_SET_TARGET
    TARGET_NAME               = "SOLAR WIND"
  END_OBJECT                  = DATA_SET_TARGET

  OBJECT                      = DATA_SET_HOST
    INSTRUMENT_HOST_ID        = "JNO"
    INSTRUMENT_ID             = "JAD"
  END_OBJECT                  = DATA_SET_HOST

  OBJECT                      = DATA_SET_MISSION
    MISSION_NAME              = "JUNO"
  END_OBJECT                  = DATA_SET_MISSION

  OBJECT                      = DATA_SET_REFERENCE_INFORMATION
    REFERENCE_KEY_ID          = "MCCOMAS2013"
  END_OBJECT                  = DATA_SET_REFERENCE_INFORMATION

  OBJECT                      = DATA_SET_REFERENCE_INFORMATION
    REFERENCE_KEY_ID          = "WILSON2014"
  END_OBJECT                  = DATA_SET_REFERENCE_INFORMATION

END_OBJECT          = DATA_SET
END