DATA_SET_DESCRIPTION |
Data Set Overview
=================
This data set contains Raw data taken by New Horizons
Solar Wind Around Pluto
instrument during the JUPITER mission phase.
During the Jupiter mission phase, SWAP used two voltage sweeping
plans: plan 0 and plan 5. Plan 0 was designed for solar wind
observations with the RPA voltage set to 105% of the center
energy of the ESA passband below 2000eV. Above 2000eV the RPA
was turned off and only the ESA was operated. In plan 0
coarse-fine scans were performed. In plan 5 the RPA was off for
the entire energy sweep.
From 01/07/2007 11:08:51 to 2/21/2007 16:42:42 SWAP was in plan
0 taking 2 minutes of data approximately every 2 hours. At
2/21/2007 17:27:31 the science team kept the plan number set at
0 and changed the the data rate such that SWAP took 1 coarse and
1 fine scan every 5 minutes. Then at 02/25/2007 19:22:43 the
team switched to plan 5 which had the RPA off and did two coarse
scans in 64 seconds every 5 minutes. From 04/14/2007 22:13:23
to 04/16/2007 06:41:06 SWAP was in plan 0, and from 04/22/2007
10:45:23 onward SWAP mostly in plan 5 until it was changed back
to plan 0.
Every observation provided in this data set was taken as a part of a
particular sequence. A list of these sequences follows:
Sequence IDs & start times (end times are the start times
of the following Sequence IDs) for the SWAP instrument
during the JUPITER phase of the New Horizons Mission
=========================================================
Sequence ID: JESW_PLACEHOLDER
Start UTC: 2007-01-01T00:00:00
Start SCLK: 1/0029915517:30912
Description: The SWAP instrument did not have any sequenced data
taken during Jupiter encounter. This entry is only a
placeholder to cover any data that exist.
For the list of observations and their parameters, refer to
the data set index table (typically INDEX.TAB & CUMINDEX.TAB,
initially in the /INDEX/ area of the data set).
Time
====
There are several time systems, or units, in use in this dataset:
New Horizons spacecraft MET (Mission Event Time or Mission Elapsed
Time), UTC (Coordinated Universal Time), and TDB Barycentric
Dynamical Time.
This section will give a summary description of the relationship
between these time systems. For a complete explanation of these
time systems the reader is referred to the documentation
distributed with the NAIF/SPICE toolkit from the NAIF PDS node.
The most common time unit associated with the data is is the
spacecraft MET. MET is a 32-bit counter on the New Horizons
spacecraft that runs at a rate of about one increment per second
starting from a value of zero at
19.January, 2006 18:08:02 UTC
or
JD2453755.256337 TDB.
The leapsecond adjustment (DELTA_ET = ET - UTC) over this dataset
is 65.184s.
The data labels for any given product in this dataset usually
contain at least one pair of common UTC and MET representations
of the time at the middle of the observation. Other portions
of the products, for example tables of data taken over periods
of up to a day or more, will only have the MET time associated
with a given row of the table.
For the data user's use in interpreting these times, a reasonable
approximation (+/- 1s) of the conversion between Julian Day (TDB)
and MET is as follows:
JD TDB = 2453755.256337 + ( MET / 86399.9998693 )
For more accurate calculations the reader is referred to the
NAIF/SPICE documentation as mentioned above.
Processing
==========
The data in this data set were created by a software data
processing pipeline on the Science Operation Center (SOC) at
the Southwest Research Institute (SWRI), Department of Space Studies.
This SOC pipeline assembled data as FITS files from raw telemetry
packets sent down by the spacecraft and populated the data labels
with housekeeping and engineering values, and computed geometry
parameters using SPICE kernels. The pipeline did not resample
the data.
Data
====
The observations in this data set are stored in data files using
standard Flexible Image Transport Sytem (FITS) format. Each FITS
file has a corresponding detached PDS label file, named according
to a common convention. The FITS files have image and/or table
extensions; see the PDS label plus the DOCUMENT files for a
description of these extensions and their contents.
This Data section comprises the following sub-topics:
- Filename/Product IDs
- Other sources of information useful in interpreting these Data
- CODMAC Level 2 SWAP data details
- Instrument description
- Visit Description, Visit Number, and Target in the Data Labels
- Unresolved Liens on the Data
Filename/Product IDs
--------------------
The filenames and product IDs of observations adhere to a
common convention e.g.
ALI_0123456789_0X0AB_ENG_1.FIT
^^^ ^^^^^^^^^^ ^^^^^ ^^^ ^\__/
| | | | | ^^
| | | | | |
| | | | | +--File type (includes dot)
| | | | | - .FIT for FITS file
| | | | | - .LBL for PDS label
| | | | | - not part of product ID
| | | | |
| | | | +-- Version number from the SOC
| | | | (Science Operations Center)
| | | |
| | | +--ENG for CODMAC Level 2 data *
| | | SCI for CODMAC Level 3 data *
| | |
| | +--Application ID (ApID) of the telemetry data
| | packet from which the data come
| |
| +--MET (Mission Event Time) i.e. Spacecraft Clock
|
+--Instrument designator
* For those datasets where the NH project is delivering
CODMAC Level 1 & 2 data (REX & PEPSSI), ENG and SCI apply
to CODMAC Level 1 & 2 data, respectively.
Instrument Instrument designators ApIDs
=========== ================================== =============
SWAP SWA 0X584 - 0X586
* Not all values in this range are used
There are other ApIDs that contain housekeeping values and
other values. See the documentation for more details.
Here is a summary of the types of files generated by each ApID
along with the instrument designator that go with each ApID:
ApIDs Data product description/Prefix(es)
===== ===================================
0x584 - SWAP Science Real-Time/SDC
0x585 - SWAP Science Summary/SWA
0x586 - SWAP Science Histogram Header/SWA
0x587 - SWAP Science Histogram Data/SWA
Other sources of information useful in interpreting these Data
--------------------------------------------------------------
Refer to the following files for more information about these data
NH Trajectory table:
/DOCUMENT/NH_TRAJECTORY.*
SWAP Field Of View definitions:
/DOCUMENT/NH_FOV.*
/DOCUMENT/NH_SWAP_V###_TI.TXT
SWAP Data summary plots:
/DOCUMENT/DATA_SUMMARY_PLOTS/SWAP_###DAY_YYYYMMDDHH_#.*
Instrument description
----------------------
Refer to the following files for a description of this instrument.
CATALOG
SWAP.CAT
DOCUMENTS
SWAP_SSR.*
NH_SWAP_V###_TI.TXT (### is a version number)
SOC_INST_ICD.*
Visit Description, Visit Number, and Target in the Data Labels
---------------------------------------------------------------
The observation sequences were defined in Science Activity
Planning (SAP) documents, and grouped by Visit Description and
Visit Number. The SAPs are spreadsheets with one Visit Description
& Number per row. A nominal target is also included on each row
and included in the data labels, but does not always match with the
TARGET_NAME field's value in the data labels. In some cases, the
target was designated as RA,DEC pointing values in the form
``RADEC=123.45,-12.34'' indicating Right Ascension and Declination,
in degrees, of the target from the spacecraft in the Earth
Equatorial J2000 inertial reference frame. This indicates either
that the target was either a star, or that the target's ephemeris
was not loaded into the spacecraft's attitude and control system
which in turn meant the spacecraft could not be pointed at the
target by a body identifier and an inertial pointing value had to
be specified as Right Ascension and Declination values. The PDS
standards do not allow putting a value like RADEC=... in the PDS
TARGET_NAME keyword's value; in those cases the PDS TARGET_NAME
value is set to CALIBRATION.
Unresolved Liens on the Data
----------------------------
None exist at the present time.
Ancillary Data
==============
The geometry items included in the data labels were computed
using the SPICE kernels archived in the New Horizons SPICE
data set, NH-X-SPICE-6-JUPITER-V1.0.
Reference Frame
===============
Geometric Parameter Reference Frame
-----------------------------------
Earth Mean Equator and Vernal Equinox of J2000 (EMEJ2000) is the
inertial reference frame used to specify observational geometry
items provided in the data labels. Geometric parameters are based
on best available SPICE data at time of data creation.
Epoch of Geometric Parameters
-----------------------------
All geometric parameters provided in the data labels were
computed at the epoch midway between the START_TIME and
STOP_TIME label fields.
Software
========
The observations in this data set are in standard FITS format
with PDS labels, and can be viewed by a number of PDS-provided
and commercial programs. For this reason no special software is
provided with this data set.
Contact Information
===================
For any questions regarding the data format of the archive,
contact the person whose PDS_USER_ID is DMCCOMAS
as described in PERSONNEL.CAT.
|
CONFIDENCE_LEVEL_NOTE |
Confidence Level Overview
=========================
During the processing of the data in preparation for
delivery with this volume, the packet data associated with each
observation were used only if they passed a rigorous verification
process including standard checksums.
In addition, raw (Level 2) observation data for which adequate
contemporary housekeeping and other ancillary data are not available
are not reduced to calibrated (Level 3) data. This issue is raised
here to explain why some data products in the raw data set,
NH-J-SWAP-2-JUPITER-V2.0,
do not have corresponding data products in the calibrated data set,
NH-J-SWAP-3-JUPITER-V2.0.
Review
======
The data have been reviewed and validated by the instrument team
members, as well as by SOC personnel.
SWAP updates for Data Sets V2.0
===============================
New columns in REAL_TIME data extension
---------------------------------------
Added the center energy for given RPA and ESA voltages to the
REAL_TIME data extension. The column names are ENERGY_0 and
ENERGY_1 in eV and correspond to the 1st and 2nd measurement
in a given packet (row).
Calibration corrections
-----------------------
Corrected the background subtraction. Corrected a rounding
error in the time used to calculate the spin angles in the SPICE
extension and fixed a small offset in the times for the spectrogram
in the TIME_LABEL_SPECT extension.
Miscellaneous calibration corrections
-------------------------------------
Added 1-day and 10-day plots under the documents directory
in a folder called data_summary plots.
|