DATA_SET_DESCRIPTION |
Data Set Overview
=================
A UDS data files
Eight files are provided that conform to the UDS conventions
regarding the naming of files and the format of the data. The
eight files are divided into 4 pairs of files with each pair
consisting of a file containing data averaged over a 10 minute
period and a file containing the maximum data value during the
same 10 minute period. The 4 pairs of file contain data for
the RAR, the PFR, WFA - magnetic field, and WFA - magnetic
field.
A.2 Plasma Frequency Receiver
To reduce the size of the UDS files only 16 frequency channels
are given which represent the combination of every 2 adjacent
channels.
The UDS average data files are computed by averaging the
Ex-average data values all data that falls in each 10 minute
period for each of the 32 channels. Then adjacent channels
are averaged together to yield the 16 channels present in the
UDS files.
The UDS peak data files are computed by finding the the peak
value of the Ex-peak data that falls in the 10 minute period.
Then the peak of adjacent channels is found to yield the 16
channels present in the UDS files.
Because of the limited usefulness of fixed-frequency data when
averaged, it has been ignored when creating the UDS files so
these 1 hour intervals of fixed-frequency will be replaced by
the 'bad data' value of -9.99e+10.
Data
====
File names (following PDS convention):
Tyyddd.TAB -> Average data
Tyyddd.TAB -> Peak data
yy: Last two digits of year.
ddd: Day of year (001..366).
The files are Ascii and contain one line for each time period
(even if there are no valid data for a time period) so they
contain 144 lines each. The format of the data is indicated
by the following Fortran read statement which can be used to
read the files:
DIMENSION F(16)
READ(1,100) TIME,MODE,BPS,F
100 FORMAT(A24,1X,A2,A1,16(1X,1PE9.2))
These variables are defined as follows:
TIME: spacecraft event time in the format
yyyy-mm-ddThh:mm:ss.sssZ
MODE: PFR scan mode:
1: Fast mode.
2: Slow mode.
3: Fixed frequency mode. This value should not occur as
fixed frequency data is removed from the UDS data.
4: The mode switched from fast to slow or slow to fast
during the averaging interval.
5: Unknown mode. This value occurs if there was no valid
data during the averaging interval. This could be due
to a data gap or bad data. Data acquired while the PFR
is in fixed tune mode is ignored so this value for the
MODE will also occur if the PFR was in fixed tune mode
during the entire averaging interval.
BPS: Telemetry bit rate:
1: 128 bps.
2: 256 bps.
3: 512 bps.
4: 1024 bps.
5: Bit rate changed during averaging period.
6: Bit rate unknown.
F: Contains the PFR data (either average or peak values,
depending on the file) of the 16 frequency channels. The
frequencies given below are the average of the two adjacent
frequencies that are combined.
F(1): 0.61 kHz
F(2): 0.80 kHz
F(3): 1.04 kHz
F(4): 1.35 kHz
F(5): 1.77 kHz
F(6): 2.30 kHz
F(7): 3.01 kHz
F(8): 3.92 kHz
F(9): 5.11 kHz
F(10): 6.67 kHz
F(11): 8.70 kHz
F(12): 11.34 kHz
F(13): 14.79 kHz
F(14): 19.30 kHz
F(15): 25.16 kHz
F(16): 32.82 kHz
NOTES:
These data are electric field intensities detected by the
Plasma Frequency Receiver (PFR) on the X antenna of the URAP
instrument. Units: microvolt/Hz**.5 measured at the receiver
input terminals. To convert to electric field strength the
given data must be divided by the effective length of the
antenna. This is complicated by the fact that the effective
length depends on the antenna impedance which is affected by
the plasma conditions local to the Ulysses spacecraft. The
impedance will also depend on the frequency. In general, the
PFR frequencies can be affected by the plasma so a single
number cannot be used for the effective antenna length.
Time resolution: 10 minutes
Fill value for bad or missing data is -9.99e+10
SUMMARY PLOTS
=============
URAP SUMMARY PLOT DESCRIPTION
A URAP Summary Plot is a plot of one day of Ulysses Unified Radio
and Plasma (URAP) experiment data. The URAP experiment consists
of five instruments: Radio Astronomy Receiver (RAR), Plasma
Frequency Receiver (PFR), Wave Form Analyzer (WFA), Fast Envelope
Sampler (FES), and Sounder (SND). The Summary Plot consists of
six plot panels. Data are plotted in the form of dynamic spectra
(3 dimensional plots of wave intensity versus frequency and time,
with the degree of darkness proportional to the wave intensity.
Frequency is plotted along the vertical axis, and time along the
horizontal axis.
Most of the data are stretched (assigned a grey shade) between
minimum and maximum data values, the maximum being the minimum
plus dynamic range designated for a receiver. The specified
dynamic ranges are shown at the right side of the plot, under the
heading 'Dyn. Range'. A linear interpolation is done between
minimum and maximum values to determine the degree of darkness of
the plotted data point. Data at or below the minimum are plotted
as white, and data at or above the maximum value are shown as
black. The pixel-font uses a 4x4 dot pattern to represent 16
shades of gray.
The plot consists of six panels, the first four of which are
plotted with time along the horizontal axis. For these plots the
time increment is 128 seconds, which means that 675 time steps
are represented along the horizontal axis, corresponding to 24
hours of data. For data with a higher time resolution than this,
the maximum data value occurring during a 128 second interval is
plotted. Frequency is plotted along the vertical axis.
Frequency labels such as 100K refer to 100 KHz; otherwise the
labels refer to Hz. Dynamic ranges shown at the right of the
panels are in telemetry units, except for the WFA ranges, which
are in logarithm of floating point DPU-FFT output. The panels
are described in order from top to bottom.
Panel 1 This is a dynamic spectrum of RAR X antenna electric
field data. The full set of 12 high receiver frequencies
and 64 low receiver frequencies is plotted, with
interpolation done for any missing frequencies
(extrapolation is not done). The high receiver frequencies
have a logarithmic spacing between approximately 50 KHz and
1 MHz. The low receiver frequencies are spaced linearly in
frequency between 1.25 and 48.5 KHz.
Panel 2 This panel is a dynamic spectrum of electric field data
from RAR, PFR and WFA instruments. The 12 frequencies of
the RAR high receiver Z antenna data are plotted. A gap
separates RAR and PFR data. The PFR data is the peak data
from the X antenna. Thirty-two PFR frequencies are plotted,
ranging from 0.5 to 35 KHz. When the PFR is in fixed tune
mode, there are 32 times as many PFR samples at a single
frequency. They are spread across the 32 frequencies, to
permit a better representation of the single frequency data.
Twenty-four WFA frequencies from the X electric field
antenna are plotted at the bottom of the panel. The low
receiver frequencies range between about 0.1 to 5 Hz; the
high receiver frequencies range from 9 to 448 Hz. The
frequencies are approximately logarithmically spaced. The
data plotted are average data from the WFA instrument.
Panel 3 WFA magnetic field data are plotted here. The high
receiver data (upper 12 frequencies) are always from the Y
search coil. The low receiver (lower 12 frequencies) will
be either Y or Z search coil data, depending on which search
coil was being sampled (indicated in panel 4). Frequencies
and units are as for the WFA Ex data.
Panel 4 This panel indicates various instrument statuses. A dark
line indicates an 'on' condition, and a light line indicates
'off'. Six status flags are shown. These are: a) RAR SUM:
The flag indicates whether the RAR is in summation (X+Z)
mode. A dark line indicates summation is on. There are a
pair of lines for this flag. The top line of the pair
indicates RAR high receiver summation, and the second line
indicates low RAR receiver summation. b) RAR POLAR: This
flag indicates RAR polarization mode on or off. Again, the
first of the two polarization lines is for the high receiver
and the next is for the low receiver. c) PFR Fast: a dark
line indicates that the PFR is in fast-scan mode; a light
line indicates that the mode is slow-scan; no line indicates
fixed-tune (single-frequency) mode. The fixed tune
frequency is shown during the fixed tune interval. Note
that the PFR causes a mode (and bit rate) dependent
interference in the WFA data. d) Greater than 10 Hz Ez:
This flag indicates that the WFA high receiver data is from
the Ez antenna (dark) or, alternatively, from the WFA Bz
antenna (light). Note that neither of these types of data
is plotted on the Summary Plot. (Only Ex data is plotted
for the high band EWFA; only By data is plotted for the high
band BWFA.) e) Less than 10 Hz By: This indicates whether
the magnetic data in the low receiver is from the By (dark)
or Bz (light) antenna. This flag does correspond to the
data plotted for the B lo receiver. f) 1024 bps: A dark
line indicates 1024 bps data. A light line indicates 512
bps. A blank corresponds to a bit rate lower than 512 bps
or a data gap.
Panels 5,6 The bottom two side-by-side panels (to the right of
the plot label) show data for each observed FES event for
high band and low band detectors. For each event, shown by
a straight horizontal line, 1024 data points are taken. On
the plot, however, only the maximum value of 4 contiguous
points is displayed. Up to 56 individual events may be
plotted. The events are plotted from bottom to top of panel
in order of their occurrence. The vertical scale is time of
event in hours of the day. Each event shown represents the
most intense FES event observed during 49 formats (a format
is 32 sec at 1024 bps). These panels are in the form of
dynamic spectra; therefore the degree of darkness is
proportional to the intensity of data observed during event.
The FES low and hi band plots show two vertical lines at the
beginning of each plot. These indicate the instrument
antenna and filter status. For the FES high band the Ex
antenna is flagged by a black point, and the Ez antenna by a
light point. The 6-60 kHz filter is shown by black, the
2-20 kHz filter is designated by a light point and all
filters with an upper limit of 6 kHz or lower are designated
by a blank. For the low receiver antenna, a black point
indicates Ex, a light point, Ez, and no point, the B search
coils. For the low band filter, a black point indicates
2-10 Khz, a light point .6-6 kHz, and no point indicates the
upper frequency limit is lower than 2 kHz. When the FES
receiver is attached to the B antenna, the band is always
0.01-1 kHz.
The option exists for plotting electron plasma frequency fpe, ion
plasma frequency fpi and electron gyrofrequency fce as lines on
the dynamic spectra. The fpe data is plotted on the PFR plot,
fpi is plotted on the EWFA panel, and fce is shown on the BWFA
panel. These data are obtained from Ulysses files of plasma
(SWOOPS) and magnetometer (MAG) data, provided by the respective
instrument teams.
Various plot labels are printed in the lower left-hand corner of
the Summary Plot. The first 3 lines give date of the plotted
data, version number of the Summary Plot program, and date the
plot was generated. The next 2 lines designate the RAR high and
low receiver modes at the beginning and end of the plotted time
interval. The modes are M (measure mode), L (linear sweep), and
F (freeze mode). For measure mode, the list number is given
after the '#' sign. For freeze mode, the frequency number
follows the '#' sign. For the low receiver in measure mode, 'F'
designates full list, 'E' indicates first half of list, and 'O'
implies the second half of the list is used.
The next line indicates RAR background type and offset.
Designation for the RAR background determination is as follows:
Background type '0' indicates offset values (computed minus
standard background values) and dynamic ranges may be specified
for the RAR receiver. Background type '1' indicates that for
each frequency a background is computed from the data for that
day, and a histogram of data minus background for all frequencies
is used to automatically set the offset and dynamic range for
each RAR receiver. The offset and range depend on the percentage
of white and black pixels chosen by the user. The offsets
(either chosen or computed) are shown after the '/'. The 3
offsets shown correspond to offsets for the RAR X high, X low,
and Z high, respectively.
The next line shows the minimum and maximum data values in
telemetry units for the RAR low X data for the day. In the next
3 lines, distances and angles are given as determined using
various locations, namely, Ulysses (U), Sun (S), Jupiter (J), and
Earth (E). The last 2 lines give the longitude and latitude of
the spacecraft in either heliographic coordinates (_H) or
ecliptic coordinates (_E), as determined from the SEDR database.
Backgrounds may be computed from the data. This is done
separately for each RAR receiver (RAR X high, RAR X low, RAR Z
high) as well as for the non-RAR receivers (PFR, WFA high, WFA
low, B WFA high and B WFA low). The goal is to achieve a full
utilization of the gray scale. To accomplish this, a percentage
of white and black pixels is specified, typically 4% white and 4%
black. Histograms of the data values are computed for each
panel. The background and range are defined by these histograms;
i.e. they are calculated to provide the percentages of black and
white pixels specified.
|